RFID Card Registration
The ES-K70 supports up to 100 RFID cards. There are two modes:
- All-at-once — register multiple cards without assigning specific slot numbers. Fastest when you only need a few cards.
- One-by-one — assign each card to a specific 3-digit slot number (001 – 100). Useful when you want to delete a single lost card later.
:::tip Compatibility Only EPIC-compatible 13.56 MHz RFID cards work with this lock. Cards included in the original box are pre-registered as a courtesy in some regions, but the manual states that in-box cards are not registered by default — register them yourself. :::
:::caution Always register with the door open. If something goes wrong, you don't want to be locked out. :::
Mode A — All-at-once registration
Best for: registering a handful of cards without caring about slot numbers.
① Open the battery cover
Open the inner-body battery cover to reach the Registration button.
② Press the Registration button
Press the Registration button once. A short beep confirms registration mode is active.
③ Enter the current PIN, then *
Enter your current PIN, then press *.
④ Press 2
Press the number 2 button to select all-at-once mode.
⑤ Place each card on the reader
One at a time, place each card on the RFID card reader on the outer body. After each card, you should hear a beep. The number pad will briefly display the assigned slot (e.g. 001, 002, …).
⑥ Press Registration to finish
Press the Registration button again. The lock beeps to confirm registration is complete.
Note
- Up to 100 cards total can be registered across both modes.
- Repeat step ⑤ before the 10-second timeout to add more cards. After 10 s without activity, registration cancels.
- After the 100th card is registered, no further cards can be added until you delete one or more.
Mode B — One-by-one registration
Best for: large deployments or when you need to be able to delete a specific lost card.
① Open the battery cover
Open the inner-body battery cover.
② Press the Registration button
Press the Registration button once. A beep confirms registration mode is active.
③ Enter the current PIN, then *
Enter the current PIN, then press *.
④ Press 2
Press 2 to select registration mode.
⑤ Enter the 3-digit slot, then #
Enter the 3-digit slot number (001 – 100) you want this card to occupy, then press #.
The slot number must always be 3 digits.
1is invalid; use001.
⑥ Place the card on the reader
Hold the card on the RFID card reader. A beep confirms, and the slot number flashes on the number pad.
⑦ When the pad returns to standby
The number pad returns to its normal display when the lock is back in standby mode.
⑧ Register more cards (optional)
- To register additional cards: while all 9 segments of the pad are lit, enter the next slot number +
#, then place the next card. Repeat as needed. - When there are no more cards: press the Registration button to finish.
Quick-reference card
╔═══════════════════════════════════════════════════════╗
║ REGISTER RFID — door open ║
╠═══════════════════════════════════════════════════════╣
║ ALL-AT-ONCE ║
║ 1. Open cover ║
║ 2. [Registration] → beep ║
║ 3. PIN + [✱] ║
║ 4. [2] ║
║ 5. Tap card on reader (repeat per card) ║
║ 6. [Registration] → finish ║
║ ║
║ ONE-BY-ONE ║
║ 1. Open cover ║
║ 2. [Registration] → beep ║
║ 3. PIN + [✱] ║
║ 4. [2] ║
║ 5. Slot (001–100) + [#] ║
║ 6. Tap card on reader ║
║ 7. (Optional) Slot + [#] + tap next card ║
║ 8. [Registration] → finish ║
║ ║
║ Capacity: 100 cards · Timeout: 10 s between steps ║
╚═══════════════════════════════════════════════════════╝
Need to remove a card?
If a card is lost or stolen, see RFID Card Deletion.